FORCE-5 5-band Cellphone Amplifier
FORCE-5 5-band Cellphone Amplifier

FORCE-5 (CM5000-80) | 3G/4G 5-Bands Large Building Cell Phone Amplifier

80dB (Cellular/ PCS/ AT&T LTE/ Verizon LTE/ T-Mobile AWS) | Boost Signal for large buildings up to 80,000 sq. ft. [ USA Product Only ]

Click to Enlarge

  • Patent pending
  • Supports All 2G, 3G and 4G standards except Sprint/WiMax
  • High Linearity
  • Reconfigurable 5-band, fits any size building
  • Automatic Shutdown to prevent interference to cell towers
  • Supports 100+ multiple users
  • Uplink/Downlink Oscillation detection(individual LEDs)
The SureCall FORCE-5 is the first five-band cell phone amplifier with highest integration on the market today. Built with High Linearity, it combines PCS and Cellular dual-bands with LTE and AWS frequencies for Verizon, AT&T and T-Mobile as a total cellular amplification solution.

 

This full-featured amplifier includes adjustable gain control and automatic shutdown for maximum flexibility. Extremely competitively priced, it requires 1/5th the space requirements of its competitors and is a fraction of the cost compared to similar amplifiers with its capabilities. Ideal for locations with a low cellphone signal and/or requiring large coverage. Covers up to 80,000 square feet (7,400m2) with good signal.

 

Package Includes:
  ▪ FORCE-5 cell phone amplifier
  ▪ AC power supply
  ▪ User manual
  ▪ Mounting kit


*Outdoor and indoor antennas and cables are required for installation (purchased separately).

Frequency Uplink: 1850-1910/824-849/698-716/776-787/1710-1755 Downlink: 1930-1990/869-894/728-746/746-757/2110-2155
Average Gain 80dB
Maximum Gain 85dB
VSWR ≤2:0
Standard Supported CDMA, GSM, UMTS, WCDMA, HSPA(+), EVDO, LTE and all other standard cell phone networks
AC Power Transformer Input AC110V, 60Hz; Output: DC19V
Maximum RF Output Power 27 dBm with High Linearity
Noise Figure 7dB
Cable LMR400 or CM400 recommended
RF connectors N Female connectors on both ends
Power Consumption <65W
Dimensions 14.5” x 11” x 3.5”
Weight 19.5 lbs
Input Impedance 50 ohm
VSWR ≤2:0
DC Power 19V

Note: Our boosters and amplifiers cannot transmit cell signals without an outside and inside antenna connected by a cable.

We strongly recommend these antennas and cables as accessories for our boosters and amplifiers.

However, the number of antennas, length of cable, or connectors needed can vary according to the size and make of the structure, lack of signal strength, or where the structure resides. Or you can contact us or our reseller to find out what you need.


CM288W


Full Band Outside Fiber Antenna

CM222W


Full Band Inside Dome Antenna  

CM400


Ultra-Low-Loss Coaxial Cable  

splitters

CM-WS(Option)


  Full Band 2,3 or 4 Way Splitters   

The signal is received by the outside antenna from the cell tower, then AMPLIFIED and transmitted to your phone through the inside antenna. When the phone transmits, the signal is received by the inside antenna, then AMPLIFIED and transmitted to the cell tower through the outside antenna.

Steps
1. Mount outside antenna (mounting kit with stucco screws provided)

2. Using CM400 cable, connect the dome antenna to the side of amplifier marked OUTSIDE

3. Mount dome antenna on the ceiling, 

4. Mount amplifier as recommended in user guide

5. Using CM400 cable, connect the dome antenna to the side of amplifier marked INSIDE

6. Connect the Power Cord (make sure the booster’s power switch is in the OFF position).

7. Turn on the booster’s power switch. The LED light will glow, indicating that the booster is ready to use.

7. Adjust dipswitches per the user manual’s instructions for ideal reception
  • AWS band, top left
  • PCS band, top right
  • LTE band, bottom left

  • Cellular band, bottom right



Where to Buy

New Products
Boosters & Kits
Antennas
Other Accessories
Support
Tell a Friend
Contact Us