TriFlex-V | 3G/4G Tri-Band Cellular Signal Booster Kit for Home/Office [ Verizon LTE ]

65dB (Cellular / PCS / Verizon LTE) | Ideal for residential and offices up to 6,000 square feet

  • Highest 4G data rate in the industry
  • 65 dB cellular, 72dB PCS, 63.5 dB LTE
  • Dual Embedded CPU for smarter technology
  • Eight RSSI detectors for all inputs and outputs
  • Stealth technology incorporated – uplink becomes dormant when not in use, providing green, power saving operation
  • FCC certified for new regulations and technical standards
  • Auto Gain Control (AGC) and manually adjustable dB gain and attenuation
  • Automatic shut down
  • Independently reconfigurable for each band
  • Supports 2G and 3G voice and 4G data standards
  • Quality Out of Band Emissions (OOBE) to date)
SureCall's new TriFlex-V is a tri-band cellular booster solution that's ideal for homes and small offices where cellular reception is weak due to distance from towers, topography, building materials or structural design. This kit is specifically designed for Verizon 2G, 3G and 4G voice and data reception. Additional kits are available for AT&T and T-Mobile subscribers. These competitively priced booster kits provide enhanced voice and data for all indoor environments, the kits are designed to provide the ultimate in cell reception. The TriFlex-V signal booster kits support up to 10 simultaneous users. Our three-year warranty is a testament to our product quality.



Standard kit (model # SC-TriVH/O-72-OD-Kit) includes: outdoor Omni antenna, inside dome antenna and 30' x 75' CM coax cable


SEE ADD-ON TAB FOR MORE KIT OPTIONS


This is a CONSUMER device. BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have your provider’s consent. Most wireless providers consent to the use of signal boosters. Some providers may not consent to the use of this device on their network. If you are unsure, contact your provider. You MUST operate this device with approved antennas and cables as specified by the manufacturer. Antennas MUST be installed at least 20cm (8 inches) from any person. You MUST cease operating this device immediately if requested by the FCC or a licensed wireless service provider. WARNING. E911 information may not be provided or may be inaccurate for calls served by using this device. 

Frequency Uplink: 824-849/1850-1910/776-787 Mhz; Downlink : 869-894/1930-1990/746-757Mhz
Input Impedance 50 ohm
Average Gain 65dB
Maximum Gain 70dB
VSWR <2:0
Standard Supported LTE, HSPA+, CDMA / WCDMA,GSM,EDGE,TDMA AMP etc.
AC Power Transformer Input AC110V,60Hz; Output DC 5-15V
DC Power 12V
Maximum RF Output Power 1 Watt EIRP
Noise Figure 5dB
Cable CM400 recommended
RF connectors N Female Connectors on both ends
Power Consumption <9W
Dimensions 9.3” x 6.3” x 1.4”
Weight 3 lbs., 8 oz

Booster Kit Contents: 


All TriFlex kits include low dB loss CM400 coax cable.


TriFlex's standard kit Model # SC-TriVH/O-72 OD-KIT includes: outside omni antenna1, interior dome antenna2, 30' x 75' CM coax cable


Additional kits:


SC-TriVH/O-72-YD-KIT: Outside yagiAntenna with inside dome antenna, 30' x 75' CM coax cable

SC-TriVH/O-72OP-KIT: Interior omni antenna with interior panelantenna, 30' x 75' CM coax cable

SC-TriVH/O-72YP-KIT: Outside Yagi antenna with interior panel antenna, 30' x 75' CM coax cable


1. Omni antennas are ideal for topographies with minimal obstacles

2. Dome antennas are best suited for a central location

3. Yagi antennas are designed to reach towers that are up to 30 miles away

4. Panel antennas allow for optimum reception to targeted areas


The signal is received by the outside antenna from the cell tower, then AMPLIFIED and transmitted to your phone through the inside antenna. When the phone transmits, the signal is received by the inside antenna, then AMPLIFIED and transmitted to the cell tower through the outside antenna.
 
Steps:
1. Mount outside antenna (mounting kit with stucco screws provided)
2. Using CM400 cable, connect the indoor antenna to the side of amplifier marked OUTSIDE
3. Mount dome antenna on the ceiling or panel antenna on the wall.
4. Using CM400 cable, connect the dome antenna to the side of amplifier marked INSIDE
5. Connect the Power Cord (make sure the booster’s power switch is in the OFF position).
6. Turn on the booster’s power switch. The LED light will glow, indicating that the booster is ready to use.
Note: Make sure Inside and outside antenna are 60’ apart

Optimizing Reception Using Dials:
Step 1: When you receive the booster, the PCS (1900 MHz frequency) dial on the top and the Cellular
(800MHz frequency) dial in the middle and the  LTE (700 MHz frequency) should be each set at 65dB. If the ALERT light turns on for either band’s dial, it means that the booster is oscillating on that band. If this happens, turn down the respective dial by 5dB, or for example, from 50 to 45. The ALERT lights will flash for 20 seconds, the booster will automatically shut down, then restart.

Step 2: If the ALERT lights for either band continue to blink, turn the respective blinking knob down by
another 5dB or until the light stops flashing.

NOTE: During this process of adjusting dBs for either band, continually monitor the bars on your cell
phone to gauge reception.